Philip rosenblum at 22:37, 27 June 2006

2006-06-27T22:37:03Z

← Older revision		Revision as of 22:37, 27 June 2006
Line 1:		Line 1:
	~~[[Image:Turbo_starter.jpeg\|thumb\|right\|300px\|Electric starter motor on a stationary Diesel [[generator]]]]~~

	Both [[Otto cycle]] and [[Diesel cycle]] [[internal-combustion engine \| internal-combustion engines]] require the pistons to be moving before the [[ignition system\|ignition]] phase of the cycle. This means that the engine must be set in motion by an external force before it can power itself. Originally, a hand crank was used to start engines, but it was inconvenient and rather hard work to crank the engine up to speed. It was also highly dangerous. Even though cranks had an overrun mechanism to prevent it, when the engine started, a crank could begin to spin along with the crankshaft. The operator had to pull away immediately, or else risk a broken wrist, or worse. Moreover, as engines evolved, they became larger and compression ratios increased, making hand cranking an increasingly difficult matter.		Both [[Otto cycle]] and [[Diesel cycle]] [[internal-combustion engine \| internal-combustion engines]] require the pistons to be moving before the [[ignition system\|ignition]] phase of the cycle. This means that the engine must be set in motion by an external force before it can power itself. Originally, a hand crank was used to start engines, but it was inconvenient and rather hard work to crank the engine up to speed. It was also highly dangerous. Even though cranks had an overrun mechanism to prevent it, when the engine started, a crank could begin to spin along with the crankshaft. The operator had to pull away immediately, or else risk a broken wrist, or worse. Moreover, as engines evolved, they became larger and compression ratios increased, making hand cranking an increasingly difficult matter.

Philip rosenblum at 22:35, 27 June 2006

2006-06-27T22:35:59Z

New page

[[Image:Turbo_starter.jpeg|thumb|right|300px|Electric starter motor on a stationary Diesel [[generator]]]]

Both [[Otto cycle]] and [[Diesel cycle]] [[internal-combustion engine | internal-combustion engines]] require the pistons to be moving before the [[ignition system|ignition]] phase of the cycle. This means that the engine must be set in motion by an external force before it can power itself. Originally, a hand crank was used to start engines, but it was inconvenient and rather hard work to crank the engine up to speed. It was also highly dangerous. Even though cranks had an overrun mechanism to prevent it, when the engine started, a crank could begin to spin along with the crankshaft. The operator had to pull away immediately, or else risk a broken wrist, or worse. Moreover, as engines evolved, they became larger and compression ratios increased, making hand cranking an increasingly difficult matter.

In [[1903]], United States [[Patent]] No. 745,157 was issued to [[Clyde J. Coleman]] of New York City for an electric '''[[automobile]] self-starter'''. He had invented the first self-starter in [[1899]], but the invention was impractical.

A license to Coleman's invention was purchased by the [[Delco]] Company, later acquired by the [[General Motors Corporation]]. Coincidentally, the death of a friend from complications due to a jaw broken while hand-cranking his automobile impelled engineer [[Charles Kettering]] to replace the hand crank with an electric starter. In [[1910]], he modified Coleman's design and made it practical. It was tested successfully on Cadillac cars of [[1911]] and first installed by [[Cadillac]] on production models in [[1912]]. These starters also worked as [[generator | generators]] once the engine was running, a concept that is now being revived in [[hybrid vehicles]]. By [[1920]], nearly every car had a self-starter.

==Electric starter==
The modern starter motor is a [[series and parallel circuits | series]]-wound [[direct current]] [[electric motor]] with a [[solenoid]] [[switch]] (similar to a [[relay]]) mounted on it. When low-[[Current (electricity)|current]] power from the [[lead-acid battery | starting battery]] is applied to the solenoid (the thin, [[grey]] wire in the image above), usually through a [[Key (lock)|key]]-operated switch, it pushes out a small [[pinion]] [[gear]] on the starter motor's shaft and meshes it with the ring gear on the [[flywheel]] of the engine. The solenoid also closes high-current contacts (powered through the thick [[red]] cable in the image) for the starter motor and it starts to run. Once the engine starts, the key-operated switch is opened, a spring in the solenoid assembly pulls the pinion gear away from the ring gear, and the starter motor stops. Modern starter motors have a "bendix" — a gear and integral [[freewheel]], or overrunning clutch, that enables the flywheel to automatically disengage the pinion gear from the flywheel when the engine starts.

[[Daimler Chrysler | Chrysler]] and [[Ford Motor Company | Ford]] both contributed to the starter market, with two types that were very different to those used on vehicles today.

Chrysler manufactured a gear reduction starter employing a small gear to drive a larger gear attached to the starter's pinion gear shaft. This allowed lower current to be drawn from the battery to run the starter, and still had the initial torque needed to turn the flywheel approximately at 200 [[revolutions per minute | rpm]]. This starter is also smaller and integrates the starter solenoid in the starter case, instead of having it mounted externally. Since this design weighs less, it has also been adapted to some light aircraft engines, where minimizing weight is very important.

Ford's version was slightly more complicated. The engineers at Ford Motor Company used a "positive engagement" style starter. This type of starter eliminated the solenoid, replacing it with a moveable armature and a separate starter relay. An armature is a part made of [[ferromagnetic]] metal that is magnetized by a coil of copper ribbon wound around it, creating an electromagnet. The Ford starter operated as follows:
#The operator closed the key-operated starting switch.
#A small electric current flowed through the starter relay coil, closing the contacts and sending a large current to the starter motor assembly.
#The armature moved a pinion gear to engage the flywheel ring gear, and simultaneously closed a pair of heavy-duty contacts supplying current to the starter motor winding.
#The starter motor cranked the engine until it started. An overrunning clutch in the pinion gear uncoupled the gear from the ring gear.
#The operator released the key-operated starting switch, cutting power to the starter motor assembly.
#A spring retracted the armature, and with it, the pinion gear.
Current Ford starter designs incorporate the starter solenoid into the starter motor assembly, instead of mounting it on the firewall or on a fender.

==Pneumatic starter==
Some gas [[turbine]] engines and [[Diesel engine | Diesel engines]], particularly on [[truck | trucks]], use a pneumatic self-starter. The system consists of a geared turbine, an [[air compressor]] and a pressure tank. Compressed air released from the tank is used to spin the turbine, and through a set of reduction [[gear | gears]], engages the ring gear on the flywheel, much like an electric starter would. The engine, once running, powers the compressor to recharge the tank.

Another method, for large diesel engines, use additional valves in cylinder heads. Compressed air is let in the cylinders so that its pressure pushes pistons down when appropriate; at the upward piston movement, air is discharged through normal exhaust valves.

Since large trucks typically use air brakes, the system does double duty, supplying compressed air to the brake system. Pneumatic starters have the advantages of delivering high torque, mechanical simplicity and reliability. They eliminate the need for oversized, heavy storage batteries in [[prime mover]] electrical systems.

==Auxiliary starter engine==
A large, high power Diesel engine, such as those used in off-road [[heavy equipment]], may have a small gasoline-powered engine attached to the side as a starter.

These were also sometimes called pony engines. On some applications, they shared the same cooling system and oil supply. As the pony engine warmed up, it circulated warm coolant and warm oil in the diesel engine. In addition to making it easier to crank, it improved the service life.

==See also==
* [[Vincent Bendix]]

==Patents==
* {{US patent|745157}} - Clyde J. Coleman
* {{US patent|1050739}} - R. C. Hull
* {{US patent|1464714}} - [[Arthur Kent]]

[[Category:Automotive technologies]]
[[Category:Auto parts]]

[[de:Anlasser]]
[[fr:Démarreur]]
[[ja:セルモーター]]

Automobile self starter - Revision history

Philip rosenblum at 22:37, 27 June 2006

Philip rosenblum at 22:35, 27 June 2006